| Engine Model |
Cat® C15 |
| Rated Speed |
2000 |
| Peak Power Speed |
1600 |
| Engine Power – ISO 14396 |
449 HP (335 kW) |
| Gross Power – SAE J1995 |
456 HP (340 kW) |
| Net Power – SAE J1349 |
373 HP (278 kW) |
| Emissions |
U.S. EPA Tier 4 Final, EU Stage V, and Japan 2014 |
| Bore |
5.4 in (137 mm) |
| Stroke |
6.75 in (171.5 mm) |
| Displacement |
927 in³ (15.2 l) |
| Peak Torque – 1,200 rpm – SAE J1995 |
1778 ft·lbf (2411 N·m) |
| Torque Rise |
16% |
| Operating Weight |
116858 lb (53006 kg) |
| Rated Payload – Quarry Face |
12.5 ton (US) (11.3 t) |
| Bucket Capacity Range |
6.4-7.6 m3 (8.3-10 yd3) |
| Cat Truck Match – High Lift |
772/773/775 |
| Transmission Type |
Cat planetary power shift |
| Forward – 1 |
5 mile/h (7.3 km/h) |
| Forward – 2 |
8 mile/h (12.2 km/h) |
| Reverse – 1 |
5 mile/h (7.6 km/h) |
| Reverse – 2 |
8 mile/h (13.6 km/h) |
| Direct Drive – Forward 1 |
Lock-up disabled |
| Direct Drive – Forward 2 |
8 mile/h (12.7 km/h) |
| Direct Drive – Forward 3 |
14 mile/h (22 km/h) |
| Direct Drive – Forward 4 |
24 mile/h (39 km/h) |
| Direct Drive – Reverse 1 |
Lock-up disabled |
| Lift/Tilt System – Circuit |
EH – Load Sense |
| Direct Drive – Reverse 2 |
9 mile/h (14.1 km/h) |
| Direct Drive – Reverse 3 |
16 mile/h (25 km/h) |
| Lift/Tilt System |
2X x 145 cc Variable displacement piston |
| Direct Drive – Reverse 4 |
25.4 mile/h (40.8 km/h) |
| Maximum Flow at 2,165 rpm |
159 gal/min (600 l/min) |
| Relief Valve Setting – Lift/Tilt |
4598 psi (31700 kPa) |
| Cylinders, Double Acting – Lift, Bore and Stroke |
190 mm x 1216 mm (7.5 in x 48 in) |
| Cylinders, Double Acting – Tilt, Bore and Stroke |
170 mm x 722 mm (6.7 in x 28.4 in) |
| Pilot System |
Variable displacement piston |
| Tilt Cylinder – Stroke |
27 in (685 mm) |
| Rack Back |
3.8 s (3.8 s) |
| Raise |
7.5 s (7.5 s) |
| Dump |
3 s (3 s) |
| Lower Float Down |
4.6 s (4.6 s) |
| Total Hydraulic Cycle Time – Empty Bucket |
18.9 s (18.9 s) |
| Steering System – Circuit |
Pilot, load sensing |
| Steering System – Pump |
Piston, variable displacement |
| Maximum Flow |
52 gal (US) (200 l/min) |
| Relief Valve Setting – Steering |
4000 psi (27600 kPa) |
| Total Steering Angle |
70° |
| Steering Cycle Times – High Idle |
3 s (3 s) |
| Steering Cycle Times – Low Idle |
5.2 s (5.2 s) |
| Air Conditioning |
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.8 kg of refrigerant which has a CO2 equivalent of 2.574 metric tonnes. |
| Front |
Fixed |
| Rear |
Trunnion |
| Oscillation Angle |
+/-12.5° |
| Brakes |
ISO 3450:2011 |
| ROPS/FOPS |
ROPS/FOPS meet ISO 3471:2008 and ISO 3449:2005 Level II standards |
| Fuel Tank |
141 gal (US) (535 l) |
| Cooling System |
27 gal (US) (101 l) |
| Engine Crankcase |
9 gal (US) (34 l) |
| Diesel Exhaust Fluid Tank |
5.5 gal (US) (21 l) |
| Transmission |
20 gal (US) (75 l) |
| Differential – Final Drives – Front |
49 gal (US) (186 l) |
| Differential – Final Drives – Rear |
45 gal (US) (170 l) |
| Note |
Cat U.S. EPA Tier 4 Final, EU Stage V, and Japan 2014 diesel engines are required to use ULSD (ultra-low sulfur diesel fuel with 15 ppm of sulfur or less) or ULSD blended with the following lower-carbon intensity fuels up to: – 20% biodiesel FAME (fatty acid methyl ester)* – 100% renewable diesel, HVO (hydrotreated vegetable oil) and GTL (gas-to-liquid) fuels. Refer to guidelines for successful application. Please consult your Cat dealer or “Caterpillar Machine Fluids Recommendations” (SEBU6250) for details. *Engines with no aftertreatment devices can use higher blends, up to 100% biodiesel. **For use of blends higher than 20% biodiesel, consult your Cat dealer |
| Operator Sound Level (ISO 6396) |
72 dB(A) (72 dB(A)) |
| Machine Sound Level (ISO 6395) |
110 dB(A) (110 dB(A)) |
| Note (1) |
The operator sound pressure level was measured according to the test procedures and conditions specified in ISO 6396:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed. |
| Note (2) |
Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment. |
| Note (3) |
The machine sound power level was measured according to the test procedures and conditions specified in ISO 6395:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed. |
| Ground to Top of ROPS |
13.5 ft (4100 mm) |
| Ground to Top of Exhaust Stacks |
13.3 ft (4060 mm) |
| Ground to Top of Hood |
10.7 ft (3270 mm) |
| Rear Axle – Centerline to Bumper |
10.3 ft (3132 mm) |
| Front Axle Centerline to Bucket Tip |
15.7 ft (4773 mm) |
| Wheel Base |
12.5 ft (3810 mm) |
| Maximum Overall Length |
39.5 ft (12042 mm) |
| Ground to Lower Hitch Clearance |
1.5 ft (459 mm) |
| Clearance at Maximum Lift |
12 ft (3732 mm) |
| Bucket Capacities |
6.4-7.6 m3 (8.3-10 yd3) |
| B-Pin Height – Maximum Lift |
18.7 ft (5755 mm) |
| Maximum Overall Height – Bucket Raised |
25 ft (7582 mm) |
| Reach – Maximum Lift |
7.7 ft (2342 mm) |
| Note |
Specifications are calculated with 6.9 m3 (9.0 yd3 ) rock bucket equipped with Michelin XLDD1 35/65 R33 tires. |
| Recyclability |
96% |
