| Net Power – SAE J1349 |
538 HP (401 kW) |
| Operating Weight |
116362 lb (52781 kg) |
| Engine Power – ISO 14396 |
580 HP (432 kW) |
| Engine Model |
Cat® C18 ™ |
| Gross Power – SAE J1995 |
588 HP (439 kW) |
| Rated Speed |
1,700 rpm |
| Peak Power Speed |
1,500 rpm |
| Emissions |
U.S. EPA Tier 4 Final, EU Stage V, and Japan 2014 |
| Bore |
5.7 in (145 mm) |
| Stroke |
7.2 in (183 mm) |
| Displacement |
1105 in³ (18.1 l) |
| Peak Torque – 1,200 rpm – SAE J1995 |
2230 ft·lbf (3023 N·m) |
| Torque Rise |
58% |
| Operating Weight – Standard |
116362 lb (52781 kg) |
| Operating Weight – High Lift |
119618 lb (54258 kg) |
| Rated Payload – Standard (Quarry Face) |
12.5 ton (US) (11.3 t) |
| Rated Payload – Loose Material (Standard) |
16 ton (US) (14.5 t) |
| Bucket Capacity Range |
4.7-13 m3 (6.2-17 yd3) |
| Transmission Type |
Cat switched reluctance electric drive |
| Forward 1 (virtual) |
4.3 mile/h (7 km/h) |
| Forward 2 (virtual) |
7 mile/h (11.3 km/h) |
| Forward 3 (virtual) |
13.8 mile/h (22.2 km/h) |
| Forward 4 (virtual) |
20 mile/h (32.1 km/h) |
| Reverse 1 (virtual) |
4.3 mile/h (7 km/h) |
| Reverse 2 (virtual) |
7 mile/h (11.3 km/h) |
| Reverse 3 (virtual) |
17.5 mile/h (28.2 km/h) |
| Lift/Tilt System – Circuit |
EH-Positive Flow Control, Flow Sharing |
| Lift/Tilt System – Pump |
Variable displacement piston |
| Maximum Flow at 1,400-1,600 rpm |
153 gal/min (580 l/min) |
| Relief Valve Setting – Lift/Tilt |
4757 psi (32800 kPa) |
| Lift Cylinder – Bore |
8.7 in (210 mm) |
| Lift Cylinder – Stroke |
41.3 in (1050 mm) |
| Tilt Cylinder – Bore |
8.7 in (269 mm) |
| Tilt Cylinder – Stroke |
27 in (685 mm) |
| Rack Back |
4.5 s (4.5 s) |
| Raise |
8 s (8 s) |
| Dump |
2.2 s (2.2 s) |
| Lower Float Down |
3.5 s (3.5 s) |
| Total Hydraulic Cycle Time |
18.2 s (18.2 s) |
| Steering System – Circuit |
Pilot, load sensing |
| Steering System – Pump |
Piston, variable displacement |
| Maximum Flow at 1,400-1,600 rpm |
71.3 gal/min (270 l/min) |
| Steering Cut Off Pressure |
4351 psi (30000 kPa) |
| Total Steering Angle |
86° |
| Steering Cycle Times – High Idle |
3.4 s (3.4 s) |
| Steering Cycle Times – Low Idle |
5.6 s (5.6 s) |
| Air Conditioning |
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.8 kg of refrigerant which has a CO2 equivalent of 2.574 metric tonnes. |
| Front |
Fixed |
| Rear |
Trunnion |
| Oscillation Angle |
13° |
| Brakes |
ISO 3450:2011 |
| ROPS/FOPS |
ROPS/FOPS meet ISO 3471:2008 and ISO 3449:2005 Level II standards |
| Fuel Tank |
147 gal (US) (555 l) |
| Cooling System – Jacket Water |
30 gal (US) (112 l) |
| Cooling Systems – Power Train |
8 gal (US) (30 l) |
| Engine Crankcase |
16 gal (US) (60 l) |
| Diesel Exhaust Fluid Tank |
8.7 gal (US) (33 l) |
| Transmission |
16 gal (US) (60 l) |
| Differential – Final Drives – Front |
49 gal (US) (186 l) |
| Differential – Final Drives – Rear |
49 gal (US) (186 l) |
| Hydraulic System – Implement/Steering |
126 gal (US) (475 l) |
| Note |
All nonroad Tier 4 Final/Stage V diesel engines are required to use: – The machine has the flexibility to run on either ultra-low-sulfur diesel fuel (ULSD with 15 ppm of sulfur or less). – Cat engines are compatible with the following renewable, alternative, and biodiesel* fuels that reduce greenhouse gases: Up to B20 biodiesel (FAME) ** Up to 100% HVO and GTL renewable fuels * Refer to guidelines for successful application. Please consult your Cat dealer or “Caterpillar Machine Fluids Recommendations” (SEBU6250) for details. – Cat DEO-ULS™ or oils that meet the Cat ECF-3, API CJ-4, and ACEA E9 specifications are required. – Only use DEF that meets ISO 22241-1 standards. |
| Operator Sound Level (ISO 6396) |
72 dB(A) (72 dB(A)) |
| Machine Sound Level (ISO 6395) |
109 dB(A) (109 dB(A)) |
| Note (1) |
The operator sound pressure level was measured according to the test procedures and conditions specified in ISO 6396:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed. |
| Note (2) |
Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment. |
| Note (3) |
The machine sound power level was measured according to the test procedures and conditions specified in ISO 6395:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed. |
| Ground to Top of ROPS |
13.8 ft (4202 mm) |
| Ground to Top of Exhaust Stacks |
14.8 ft (4498 mm) |
| Ground to Top of Hood |
10.9 ft (3334 mm) |
| Ground to Bumper Clearance |
3.1 ft (933 mm) |
| Rear Axle – Centerline to Bumper |
10.5 ft (3187 mm) |
| Front Axle Centerline to Bucket Tip |
14 ft (14 mm) |
| Wheel Base |
14.9 ft (4550 mm) |
| Maximum Overall Length |
39.3 ft (11991 mm) |
| Ground to Lower Hitch Clearance |
1.9 ft (568 mm) |
| Ground to Center of Axles |
3.2 ft (978 mm) |
| Clearance at Maximum Lift |
11.9 ft (3641 mm) |
| B-Pin Height – Maximum Lift |
18 ft (5479 mm) |
| Maximum Overall Height – Bucket Raised |
24.5 ft (7455 mm) |
| Reach – Maximum Lift |
6.5 ft (1981 mm) |
| Note |
Specs are calculated with 6.9 m3 (9.0 yd3) rock bucket and Michelin XLDD2 with 978 mm (3.2 ft) centerline of rear axle height. |
| Ground to Top of ROPS |
13.8 ft (4202 mm) |
| Ground to Top of Exhaust Stacks |
14.8 ft (4498 mm) |
| Ground to Top of Hood |
10.9 ft (3334 mm) |
| Ground to Bumper Clearance |
3.1 ft (933 mm) |
| Rear Axle – Centerline to Bumper |
10.5 ft (3187 mm) |
| Front Axle Centerline to Bucket Tip |
15.3 ft (4661 mm) |
| Wheel Base |
14.9 ft (4550 mm) |
| Maximum Overall Length |
40.7 ft (12398 mm) |
| Ground to Lower Hitch Clearance |
1.9 ft (568 mm) |
| Ground to Center of Axles |
3.2 ft (978 mm) |
| Clearance at Maximum Lift |
13.3 ft (4043 mm) |
| B-Pin Height – Maximum Lift |
19.3 ft (5881 mm) |
| Maximum Overall Height – Bucket Raised |
25.8 ft (7849 mm) |
| Reach – Maximum Lift |
6.8 ft (2062 mm) |
| Note |
Specs are calculated with 6.9 m3 (9.0 yd3) rock bucket and Michelin XLDD2 with 978 mm (3.2 ft) centerline of rear axle height. |
| Ground to Top of ROPS |
13.8 ft (4221 mm) |
| Ground to Top of Exhaust Stacks |
13.8 ft (4214 mm) |
| Ground to Top of Hood |
10.9 ft (3334 mm) |
| Ground to Bumper Clearance |
3.1 ft (933 mm) |
| Rear Axle – Centerline to Bumper |
10.5 ft (3187 mm) |
| Front Axle Centerline to Fork Tip |
16.5 ft (5023 mm) |
| Wheel Base |
14.9 ft (4550 mm) |
| Maximum Overall Length |
41.9 ft (12761 mm) |
| Ground to Lower Hitch Clearance |
1.9 ft (568 mm) |
| Ground to Center of Front Axle |
3.2 ft (978 mm) |
| Fork Height with Level Arms |
8.1 ft (2474 mm) |
| Fork Top Clamp Opening |
13.1 ft (4006 mm) |
| Fork Height at Maximum Lift |
17.2 ft (5242 mm) |
| Hinge Pin Height at Maximum Lift |
16.1 ft (4918 mm) |
| Dump Angle at Maximum Lift |
-39.4 ° (-39.4 °) |
| Bucket Capacities |
4.7-13 m3 (6.2-17 yd3) |
| Recyclability |
96% |
