| Nominal Rated Payload |
327 ton (US) (297 t) |
| Rated Gross Machine Weight |
1150000 lb (521631 kg) |
| Gross Power – SAE J1995 |
3500 HP (2610 kW) |
| Standard Gross Power – SAE J1995 |
3500 HP (2610 kW) |
| Engine Model |
Cat® C175-16 |
| Optional Gross Power – SAE J1995 |
3100 HP (2312 kW) |
| Optional Gross Power – SAE J1995 (Option 2) |
2750 HP (2051 kW) |
| Rated Speed |
1800 r/min (1800 r/min) |
| Standard Tires |
53/80 R63 |
| Total Reduction Ratio |
35:01:00 |
| Net Power – SAE J1349 |
3405 HP (2539 kW) |
| Rims |
36″ x 63″ |
| Service Brakes |
Four-Corner, Wet Disc, Oil Cooled, Hydraulically Actuated |
| Total Reduction Ratio |
35:01:00 |
| Emissions Rating |
Fuel Optimized |
| Top Speed – Loaded |
37 mile/h (60 km/h) |
| Note (1) |
Quick Change Rims optional. |
| Bore |
6.9 in (175 mm) |
| Note (2) |
Caterpillar recommends the customer evaluate all job conditions and consult tire manufacturer for proper tire selection and TKPH (TMPH) capabilities. |
| Struck |
108-133 m³ (142-175 yd³) |
| Pump Flow – High Idle (HAA at 1,800 rpm) |
221 gal/min (840 l/min) |
| Front Axle – Empty |
49 % (49 %) |
| Fuel Tank |
1300 gal (US) (4922 l) |
| Generator/Alternator |
Brushless, engine mounted, dual bearing |
| Front Wet Disc Brake Surface Area |
20378 in² (131473 cm²) |
| Displacement |
5187 in³ (85 l) |
| Stroke |
8.7 in (220 mm) |
| Rear Axle – Empty |
51 % (51 %) |
| Cooling System |
211 gal (US) (799 l) |
| Height – Top of ROPS |
22.25 ft (6779 mm) |
| Rear – Wet Disc Brake Surface Area |
30750 in² (198388 cm²) |
| Heaped (SAE 2:1) |
180-222 m³ (236-290 yd³) |
| Pump Flow – High Idle (LAA at 1,960 rpm) |
240 gal/min (910 l/min) |
| Controls |
IGBT Inverter Technology, air cooled, pressurized cabinet with filtration |
| Chassis Weight |
426237 lb (193338 kg) |
| Overall Length |
50.75 ft (15463.5 mm) |
| Wheel Motor |
High-torque AC induction, rear axle mounted |
| Crankcase |
82 gal (US) (310 l) |
| Front Axle – Loaded |
33 % (33 %) |
| Relief Valve Setting – Raise |
3029 psi (20884 kPa) |
| Dump Body Plate Thickness Varies Depending on Body Selection – Floor Plate |
0.63 in (16 mm) |
| Cooling System |
Variable speed, hydraulically driven cooling system |
| Wheel Base |
21.83 ft (6644.5 mm) |
| Dump Body Plate Thickness Varies Depending on Body Selection – Front Plate |
0.35 in (9 mm) |
| Body Raise Time – High Idle |
24 s (24 s) |
| Final Drive – Each |
67 gal (US) (254 l) |
| Body Weight |
64346 lb (29187 kg) |
| Rear Axle – Loaded |
67 % (67 %) |
| Standards |
ISO 3450:2011 |
| Rear Axle – Tail |
15.5 ft (4716 mm) |
| Dump Body Plate Thickness Varies Depending on Body Selection – Side Plate |
0.31 in (8 mm) |
| High Idle Body Lower Time – Float |
20 s (20 s) |
| Parking Brake |
Four-corner, Multi-disc, Spring applied, Hydraulically Released |
| Hydraulic Tank |
296 gal (US) (1121 l) |
| Ground Clearance |
2.67 ft (906 mm) |
| Dump Body Plate Thickness Varies Depending on Body Selection – Canopy Plate |
0.2 in (5 mm) |
| Total Cycle Time |
44 s (44 s) |
| ROPS Standards (1) |
Rollover Protective Structure (ROPS) meets ISO 3471:2008 criteria for operator and ISO 13459:2012 for trainer. |
| Hydraulic System – Including Tank |
385 gal (US) (1458 l) |
| Load Brake |
Rear service brakes |
| Dump Clearance |
3 ft (1555 mm) |
| Sound Standards (1) |
The operator sound pressure level measured according to work cycle procedures specified in ISO 6394 and 6396 is 75 dB(A) for cab offered by Caterpillar when properly installed, maintained, and tested with doors and windows closed. |
| FOPS Standards |
Falling Object Protective Structure (FOPS) meets ISO 3449:2005 Level II for operator and ISO 13459:2012 Level II for trainer. |
| Dynamic Retarding Power – Continuous |
5480 HP (4086 kW) |
| Loading Height – Empty |
22.92 ft (6995 mm) |
| Sound Standards (2) |
Hearing protection may be needed when operating with an open operator station and cab (when not properly maintained or doors/windows open) for extended periods or in a noisy environment. |
| Steering Standards |
ISO 5010:2007 |
| Overall Height – Body Raised |
48.42 ft (14747 mm) |
| Centerline Front Tire Width |
23 ft (7024 mm) |
| Front Axle Clearance |
3.17 ft (969 mm) |
| Canopy Width (without optional rock deflectors) |
29.75 ft (9068 mm) |
| Outside Body Width |
29.75 ft (9062 mm) |
| Inside Body Width |
28.08 ft (8560 mm) |
| Front Canopy Height |
26.33 ft (8024 mm) |
| Rear Axle – Clearance |
3.08 ft (934 mm) |
| Centerline of Rear Dual Tire Width |
18.75 ft (5727 mm) |
| Overall Tire Width |
28.67 ft (8738 mm) |
| Overall Canopy Width |
31.5 ft (9611 mm) |
| Diesel Exhaust Fluid Tank |
100 gal (US) (378 l) |
| Note |
Contact your local Cat dealer for body recommendations. |
| Note (1) |
Twin, two-stage hydraulic cylinders mounted inside main frame; double-acting cylinders in both stages. |
| Note (1) |
Contact factory for high altitude configuration. |
| Steer Angle |
39 ° (39 °) |
| Note |
Gross Machine Operating Weight is 521 631 kg (1,150,000 lb). |
| Note (1) |
Consult your tire manufacturer for maximum tire load. |
| Note (1) |
DEF Tank only available for EPA Tier 4 / EU Stage V engine option. |
| Note (2) |
Tier 4 / EU Stage V option available for regions that require these emissions standards. |
| Note (2) |
Chassis weight with full fuel and fluids, standard & mandatory attachments, hoist, body mounting group, rims, and tires |
| Note (2) |
Power raise in both stages; power down in both stages possible. |
| Note (3) |
Refer to Cat Mining Truck 10/10/20 Overload Policy (AEXQ0250) for maximum gross machine weight limitations. |
| Note (3) |
Automatic body-lower modulation reduces impact on frame. |
| Note (3) |
Tier 4 / EU Stage V engine option Net Power – SAE J1349: 3434 HP (2561 kW) |
| Note (4) |
Tier 4 Final / Stage V chassis weight: 426312 lb (193372 kg) |
